This analog is for both stone model and digital model use.

This analog is for both stone model and digital model use. It is compatible with the multiunit connection for MIS® V3, C1, and Seven.

This analog is for both stone model and digital model use.

This is a final screw that takes a .050/1.27mm hex driver.  Torque is 30ncm.  This screw is compatible with MIS® Seven 3.0, MIS® C1 SP, and MIS® V3 NP. All of our screws are stress tested to 150% of the nominal torque...

This is a final screw that takes a 0.50/1.27mm hex driver. Torque is 25ncm.  The screw has M1.6 thread. It is compatible with the multiunit connection for MIS® V3, C1, and Seven. All of our screws are stress tested to 150% of the nominal...

This is a final screw that takes a .050/1.27mm hex driver.  Torque is 30ncm.   This screw is for MIS Seven, MIS C1 and MIS V3. All of our screws are stress tested to 150% of the nominal torque value and can also be used as lab screws...

This scan body is made of titanium and is designed for both intraoral use and desktop scanning. It has a fixed internal screw and the scan body is hand tightened.

This scan body is made of titanium and is designed for both intraoral use and desktop scanning. It has a fixed internal screw and the scan body is hand tightened.

This scan body is made of titanium and is designed for both intraoral use and desktop scanning. It has a fixed internal screw and the scan body is hand tightened.

This scan body is made of titanium and is designed for both intraoral use and desktop scanning. It has a fixed internal screw and the scan body is hand tightened. It is compatible with the following MIS V3, C1, and Seven. multiunit abutments. Library...

This intra-oral scan body driver enables you to tighten and loosen the intra-oral scan body in hard to reach areas.

This latch style driver is made of stainless steel and is compatible with internal .050/1.27mm hex screws. This driver is heat treated for increased durability and wear resistance. Includes laser marked identification. 

This latch style driver is made of stainless steel and is compatible with internal .050/1.27mm hex screws. This driver is heat treated for increased durability and wear resistance. Includes laser marked identification.

This premilled titanium blank is engaging, is 10mm in diameter, and has a total mill-able length of 20mm.

This premilled titanium blank is engaging, is 10mm in diameter, and has a total mill-able length of 20mm.

This ti base comes with a final screw, SKU 19.056 that takes a .050/1.27mm hex driver. The torque is 30 ncm. This ti base has a 1mm collar height. Wax up sleeve sold separately - SKU 33.001P5

This ti base comes with a wax up sleeve and a final screw, SKU 19.081 that takes a .050/1.27mm hex driver. The torque is 30 ncm. This ti base has a 1mm collar height.

This ti base comes with a wax up sleeve and a final screw, SKU 19.085 that takes a .050/1.27mm hex driver. It is designed for use on top of the MIS® multiunit for Seven®, V3®, and C1®.   The torque is 25 ncm. This ti...

This ti base comes with a final screw, SKU 19.056 that takes a .050/1.27mm hex driver. The torque is 30 ncm. This ti base has a 1mm collar height and is no longer being made with an anti-rotational flat side. Wax up sleeve sold separately...

This ti base comes with a wax up sleeve and a final screw, SKU 19.081 that takes a .050/1.27mm hex driver. The torque is 30 ncm. This ti base has a 1mm collar height and is no longer being made with an anti-rotational flat side.